Skip to content
← All articles
Flowers and Yard

How to prune shrubs without harming them

Learn when and how to prune common shrubs, which cuts to make, and how to avoid removing flower buds or shocking plants with careless trimming.

A smiling older man with white hair and a beard uses hand pruners to trim a hydrangea bush with dried flower heads in a garden.

Pruning shrubs is less about aesthetics than about keeping a plant healthy, open to light and in proportion to the space it has. Done well, it encourages strong new growth, improves flowering and removes dead or damaged wood before it invites disease. Done badly, it can remove the flower buds for the season, leave ugly stubs that never close, or stress the plant so much that it struggles for years. The difference usually comes down to timing and the cut you choose.

Most pruning mistakes happen because people treat all shrubs the same. A hedge, a hydrangea, a lilac and a boxwood each respond differently to cutting. Before you pick up a tool, identify the shrub, learn when it blooms, and decide what result you want.

Learn when to cut

The general rule is to prune spring-flowering shrubs such as lilac, forsythia and early azalea right after they finish blooming. These plants set their flower buds on last year's growth during late summer, so cutting in late winter or spring removes the buds you were hoping to see. Summer-flowering shrubs such as butterfly bush, many hydrangeas grown on new wood, and rose of Sharon can be pruned in late winter or early spring, before new growth starts.

Evergreen shrubs such as boxwood, yew and juniper can be shaped in late spring or early summer, when they are in active growth and recover quickly. Avoid heavy pruning in late summer or fall, since fresh growth that appears then may not harden off before cold weather and can be damaged.

Dead, broken or diseased wood can be removed at any time of year, which is usually the right first step when a shrub looks rough.

Make the right cut

Use sharp bypass pruners for stems up to about half an inch thick, loppers for thicker branches, and a pruning saw for anything larger. A clean cut heals faster than a torn one, so keep blades sharp and clean them between plants if you are removing diseased material. Make each cut just above a healthy bud or a side branch that faces the direction you want new growth to go, and angle the cut so water runs off rather than pooling on the cut surface.

Avoid leaving stubs. A stub that extends past the next bud will die back and invite decay into the stem. Cut back to a junction with a branch or to the base of the stem, rather than partway along it.

Use the three-cut method for big limbs

Large, heavy branches should be removed in three steps to prevent the bark from tearing down the trunk. Make a first cut from underneath, about a foot out from the trunk, and cut about a third of the way through. Make the second cut from the top, a few inches farther out, until the branch falls away. Then remove the remaining stub by cutting just outside the branch collar, the slightly swollen ring where the branch meets the trunk. Do not cut flush against the trunk, and do not leave a long stub.

Thin rather than shear

Shearing a shrub into a neat box creates dense outer growth and a bare interior that rarely fills in. Thinning, which means removing whole stems at their base or at a side branch, opens the plant to light and air and maintains its natural shape. Remove one or two of the oldest stems each year on overgrown shrubs, and spread the work over several seasons so the plant is not shocked by losing too much at once. As a general guideline, avoid removing more than about a quarter to a third of the plant in a single year.

Keep hedges wider at the base than at the top, so light reaches the lower branches. A hedge that is narrow at the bottom develops bare patches that never recover.

Keep your tools clean and dry after each use, and oil the pivot points so the blades close cleanly. Dispose of diseased clippings rather than composting them, since many fungal problems survive in plant debris. If you are unsure whether a shrub will tolerate a hard cut, prune only a few stems the first year and watch the response before removing more. Most shrubs recover from modest, well-timed cuts, but a sudden severe cut can take several seasons to correct.

Pruning steps in order

  1. Identify the shrub and whether it blooms on old or new wood.
  2. Pick the right season (after bloom for spring bloomers, late winter for summer bloomers).
  3. Sharpen and clean pruners, loppers and saw.
  4. Remove dead, broken and diseased wood.
  5. Thin one or two of the oldest stems at the base.
  6. Cut just above an outward-facing bud or side branch, leaving no stubs.
  7. Stop at a quarter to a third of the plant.
  8. Bag diseased clippings.

Plan your first cut

Identify each shrub in your yard and note whether it blooms in spring or summer. Choose one plant that needs attention, decide whether it needs thinning or shaping, and check the bloom timing before making any cuts. Start with removing dead or damaged wood, then take a few stems at a time from the oldest growth. Step back after each round and look at the plant from several angles before continuing.