How to plant a tree in your yard
Choose the right spot and tree, dig a planting hole correctly and care for a new tree through its first years so its roots establish well.
A tree planted well can shade a house, shelter wildlife and grow for decades. A tree planted poorly can struggle for years, decline early or become a hazard when its roots and canopy outgrow the space. Most failures come from decisions made before the shovel goes into the ground: a tree that is too large for the site, planted too deep, or set in a spot where it cannot reach the light, water or room it needs. Careful planning takes an afternoon and pays off for the lifetime of the tree.
The steps below apply to most bare-root, balled-and-burlapped and container trees. Ask a local nursery or your state extension service for species recommendations that suit your soil, climate and any rules about planting near utilities or property lines.
Choose the spot and the tree
Look up at the space before you choose. Measure the mature height and spread of the species, not just its size at purchase, and keep a generous distance from the house, driveway, sewer lines and overhead wires. Many street and yard trees need twenty feet or more of clearance from structures, while smaller ornamental trees can fit closer. Check whether underground utilities run through the planned site. Call 811, the free national call-before-you-dig number, a few days before you dig so utilities can mark buried lines.
Choose a species adapted to your climate and soil, and look for healthy nursery stock with a strong central trunk and an even branching structure. Avoid trees with circling or girdling roots at the base or in the container, since these will continue to press against the trunk after planting. Ask the nursery to show you the root flare, the swelling at the base where the trunk meets the roots.
Dig the hole the right way
The most important rule is that the hole should be shallow and wide. Dig a hole at least two to three times the width of the root ball, but no deeper than the distance from the bottom of the root ball to the root flare. A hole that is too deep sinks the tree and suffocates its roots, which is one of the most common causes of early death in new plantings. Loosen the soil at the sides of the hole so new roots can grow outward easily.
Set the tree in the hole so the root flare sits slightly above the surrounding soil, which allows for some settling. Remove any wire, twine or burlap from the top of the root ball, and cut away containers if the roots are circling tightly. Gently loosen circling roots with your fingers or a tool, since untangled roots grow outward more readily.
Backfill with the native soil you removed, without adding large amounts of compost or potting mix, which can create a bowl that holds water and keeps roots from spreading into the surrounding ground. Water as you backfill to remove air pockets, then finish the surface and build a shallow ring of soil around the edge to hold water.
Mulch and water
Spread two to three inches of wood chips or shredded bark over the root zone, out to the edge of the planting area, but keep the mulch several inches away from the trunk. Piling mulch against the bark invites rot and insects. A wide ring of mulch reduces competition from grass and helps hold moisture.
New trees need regular, deep watering for their first two growing seasons. A common rule is to provide roughly ten gallons a week for a young tree, applied slowly at the base so it soaks into the root zone rather than running off. Check the soil by hand a few inches down, and water more often in hot, dry weather. Slow-release watering bags or a soaker hose set near the root zone make the job easier.
Support and maintain
Stake a tree only if it cannot stand upright on its own, or if it is planted in a very windy site. Stakes should be loose enough to let the trunk move slightly, which strengthens it. Remove stakes after one year, or as soon as the tree can stand without them. Do not prune the tree at planting, except to remove broken or damaged branches. Most young trees need only a light structural prune in their first few years, once the roots have established.
Monitor the tree each season for wilting, leaf scorch, cracks in the bark and new growth that indicates a healthy root system. A tree that leafs out and extends its branches in the first full season is usually on track.
Planting steps in order
- Check mature size and clearance from structures and wires.
- Call 811 to have buried utilities marked.
- Find the root flare.
- Dig two to three times as wide as the root ball and no deeper than the flare.
- Remove wire, twine and top burlap, and loosen circling roots.
- Set the flare slightly above grade and backfill with native soil, watering as you go.
- Mulch two to three inches, kept away from the trunk.
- Water deeply weekly for two growing seasons.
Plan before you dig
Measure the space, call 811 if you plan to dig, and choose a species that will fit at maturity. Plant in the cooler part of the year when the tree is dormant, dig the hole shallow and wide, and set a reminder to water deeply each week for the first two summers. Check the root flare at planting and again after the first year.