How to check tire pressure and tread depth
Check tire pressure and tread depth at home with a gauge and a coin test, learn the right pressure for your car and know when tires need replacing.
Tires are the only part of a car that touches the road, and their condition affects braking, steering, fuel economy and safety in wet weather. Underinflated tires wear faster, run hotter and reduce handling. Worn tread loses its ability to channel water away, which raises the risk of hydroplaning. Checking pressure and tread takes only a few minutes and needs only a basic gauge and a coin, yet many drivers check their tires only when a warning light appears. A monthly check, plus a look before long trips, catches most problems early.
Both checks are simple, but they are easy to do incorrectly if you skip the details. Measure cold tires, use the right pressure for your vehicle, and read the tread across the full width of the tire.
Find the correct pressure
The recommended tire pressure is not the number printed on the tire sidewall. The sidewall shows the maximum pressure the tire can safely hold, which is usually much higher than the pressure your car needs. The correct figure is on a placard, often on the driver's door jamb, inside the fuel door or in the owner's manual. It is listed in pounds per square inch, and it is measured with the tires cold, meaning the car has been parked for at least three hours or driven less than a mile.
Note the recommended figure for the front and rear tires, since some vehicles specify different pressures for each axle. Keep the placard information in your phone or glove box, so you can check it quickly at a gas station or service center.
Check pressure with a gauge
Remove the valve cap, press the gauge firmly onto the valve stem and read the pressure. A pencil-style or digital gauge is accurate enough for home use. Compare the reading with the placard figure. If the pressure is low, add air at a gas station or with a portable compressor, checking the reading every few seconds until you reach the target. If the pressure is high, release a small amount of air with the gauge tip or the valve core, then recheck.
Check the spare tire as well, since it is often forgotten until it is needed. Compact spares usually require a higher pressure than standard tires, and the placard or the spare tire's sidewall will list the correct figure. Replace the valve caps when you finish, since they keep dirt and moisture out of the valve.
Measure tread depth with a coin
Tread depth is measured in thirty-seconds of an inch in the United States. A simple check uses a penny. Insert the penny into a tread groove with Lincoln's head pointing down. If you can see the top of his head, the tread is at or below about two thirty-seconds of an inch, which is the legal minimum in many states and the point at which tires should be replaced. If the tread covers the top of his head, the tread is still above that minimum, and the tire is not yet due for replacement on depth alone.
Check several grooves across the tire, including the middle and the edges. Uneven wear can indicate underinflation, overinflation, alignment problems or worn suspension parts. Look for bulges, cracks in the sidewall and objects embedded in the tread, and note any that look unusual.
Some tires have built-in wear bars, which appear as raised strips across the grooves. When the tread wears down to these bars, the tire needs replacing.
When to replace tires
Replace tires when the tread is near the legal minimum, when the sidewalls show cracks or bulges, when the tire has a puncture that cannot be safely repaired or when the tires are older than the manufacturer's recommended life, which is often six years or more depending on conditions. Tire age is printed on the sidewall as a four-digit date code, where the first two digits show the week and the last two show the year of manufacture.
Replace tires in pairs on the same axle when possible, and check the alignment after a new set is installed, since uneven wear often starts with an alignment problem.
Full check, step by step
- Check with tires cold.
- Read the door-jamb placard for front, rear and spare pressures.
- Remove the valve cap and read each tire with a gauge.
- Add or release air to the placard figure and recheck.
- Insert a penny head-down in several grooves; if you can see the top of Lincoln's head, replace the tire.
- Look for uneven wear, bulges, cracks and embedded objects.
- Read the four-digit date code.
- Replace valve caps and repeat monthly.
Make the check a habit
Find the placard in your car and write down the front and rear pressures. Buy a basic gauge and a penny if you do not have them, then check all four tires and the spare. Measure the tread in three grooves on each tire, and note any uneven wear or damage. Repeat the check monthly and before any long trip.