How to build a raised garden bed
Plan the size, materials and soil mix for a raised garden bed, with a materials list and step-by-step build that works for yards and patios.
A raised garden bed is a simple box filled with good soil, set on top of the ground or on a hard surface. It warms up earlier in spring, drains better than heavy native soil and puts the plants at a height that is easier on your back. Because you control the soil inside the frame, a raised bed is also the practical answer when your yard has clay, rocks, poor drainage or contaminated ground that you do not want to disturb.
The build itself is not complicated, but a few decisions made at the start determine how well the bed works for years. Size, depth, the material you use for the frame and the soil mix all affect how much you can grow, how often you need to water and how long the wood or other material will last. Settle these before you buy anything, and the construction will go quickly.
Size and depth
Keep the width at three to four feet at most. A bed narrower than about four feet lets you reach the center from either side without stepping on the soil, which compacts it and damages roots. Length can be whatever fits your space, though six to eight feet is a common choice. For most vegetables, a depth of about eight to twelve inches is enough. Root crops such as carrots and beets, and any deep-rooted plants, do better in a bed of twelve inches or more.
Leave at least two feet of walking space around the bed so you can move a wheelbarrow or hose past it. If the bed sits on grass, place it in a sunny area and check that the site gets roughly six to eight hours of direct light for fruiting crops.
Materials and tools
Cedar and other rot-resistant lumber are popular for frames because they last longer than untreated pine. Composite lumber and galvanized steel panels are also used. Avoid old railroad ties and pressure-treated wood treated with older preservatives, since they can leach chemicals into soil that you plan to eat from. Ask the seller or check the product label if you are unsure.
- Boards for the frame, such as two-by-eight or two-by-ten lumber, enough for a rectangle of your chosen size
- Corner brackets or stakes, typically four, to hold the corners square
- Exterior screws, rated for outdoor use
- A drill and a square or tape measure
- Landscape fabric or cardboard to lay on the ground before filling, to block grass and weeds
- Soil mix, compost and mulch, in the quantities described in the next section
Build the frame
Lay out the rectangle on the ground and check that the diagonal measurements match, since equal diagonals mean square corners. Cut the boards to length, then fasten the corners with brackets or stakes and screws. If you stack two boards to reach the target depth, offset the joints so the corners are staggered and the frame stays rigid. Set the frame on level ground, or dig out the high spot so the bottom edge sits evenly. A bed that rocks or leans will spill soil at the low corner every time it rains.
Lay the landscape fabric or a layer of plain cardboard across the bottom of the bed before filling. This blocks grass from pushing up through the soil, but it is not required and does not need to be perfect. Water the layer lightly so it settles.
The full build order is:
- Mark a level rectangle no wider than four feet in full sun.
- Cut boards to length and pre-drill.
- Fasten corners with brackets or stakes and exterior screws, staggering joints if stacking boards.
- Check the diagonals for square and level the base.
- Lay cardboard or landscape fabric and wet it.
- Fill in layers with the topsoil, compost and coarse-material mix, watering each layer.
- Let the soil settle, then mulch and plant.
Fill with the right soil
Most gardeners fill a raised bed with a blend of topsoil, compost and a bulking material. A common mixture is roughly 60 percent topsoil, 30 percent compost and 10 percent coarse material such as aged bark or perlite, though you can adjust these ratios. Buy from a supplier that can describe the mix, and ask whether the material has been screened for weed seeds and contamination. Avoid using soil from your yard unless you know it is clean, because it may carry weeds, disease or heavy metals depending on the history of the site.
Fill the bed in layers and water each layer as you go, so the soil settles before planting. Expect the level to drop by several inches over the first season as the organic matter breaks down. Top up with compost each spring to keep the bed productive.
Plant and maintain
Once the soil has settled, you can plant directly. A bed of four by eight feet can hold dozens of plants if you use intensive spacing, but crowding works only when the soil is rich and the plants get enough water. Mulch the surface to keep moisture in and cut down on weeds. Check the moisture level with a finger a few inches down, since raised beds dry out faster than in-ground gardens, particularly in summer and on windy sites.
Inspect the frame each year for loose screws, rotting boards and gaps at the corners. Repairs take minutes when caught early and can prevent a collapse of the soil structure later in the season.
Before you buy lumber
Measure the space you have, choose a width of no more than four feet, and write down a cut list before shopping. Ask a lumber supplier for rot-resistant boards and confirm the wood is suitable for food crops. Build the frame on level ground, fill it in layers and plant one or two easy crops to test how the bed holds water through your first month.